A step-by-step guide for the M-VAVE FM-1 and SMK-37 Pro / Elite. No technical knowledge needed. If something doesn't work, see If something goes wrong.
.fwsc. Use it as you downloaded it. If it came inside a .zip, take the .fwsc out of it first.Get it from the download page: it picks the right file for your computer. Then follow the steps for your system.
.zip and choose Extract All.If Windows Security deletes it, see If something goes wrong.
.dmg and drag M-Flasher into Applications.Start M-Flasher soon after you connect the unit: if it waits too long, macOS can take the unit out of download mode after about half a minute. Just connect it again.
sudo apt install ./m-flasher_…_amd64.deb (the name of the file you downloaded).sudo dnf install ./m-flasher-….rpm, or on openSUSE sudo zypper install ./m-flasher-….rpm..tar.gz and follow its README.txt.Then connect the unit (unplug and plug it in again if it was connected), and start M-Flasher from your app menu. Start it as yourself, not with sudo.
M-Flasher talks to your unit in its download mode, a special mode built into its chip that works even when the firmware is broken. How to get there depends on what your unit runs now. Pick the first one that fits:
M-Flasher finds the unit by itself, reads it for a second or two, and shows USB CONNECTED · DOWNLOAD MODE with the model, the firmware and the bootloader.
That's normal: in download mode the unit's own screen doesn't change, and nothing new appears in Explorer or Finder.
Original M-VAVE unit? With M-VAVE's own bootloader and firmware, no key combination gets you into download mode: use the DOWNLOAD MODE button.
The backup holds everything on the unit: firmware, settings, presets, sounds and its factory calibration. Backups go to Documents → M-Flasher → backups, and the BACKUPS link at the top of the window opens that folder.
Good to know: M-Flasher also saves a backup by itself before every change it makes, so you can always go back. Keep a copy of your first backup somewhere safe.
.fwsc file. The map on the right marks what will change.Your settings, presets and Bluetooth pairings stay as they are, and so does the unit's bootloader. M-Flasher checks that the file is for your model before it writes anything.
Switching to a very different firmware? Settings saved by the old one can confuse the new one, and M-Flasher warns you. To go back to the old firmware cleanly, restore a backup made while it was installed.
FM-1 sold from late 2026? These have a newer memory chip, shown as (new) next to FLASH CHIP. Some custom firmwares made before it came out don't fully work on it, for example not keeping settings. Check with the firmware's author before installing it.
The bootloader is the small program that starts your unit. m-bootloader replaces M-VAVE's with one that has a recovery menu, so you can always get back into download mode from the unit's keys, even if a firmware stops working.
When M-Flasher sees M-VAVE's original bootloader, it asks "Install m-bootloader?". Click YES, look over the summary, and click WRITE … SECTORS.
Or any time: click FLASH BOOTLOADER, leave M-BOOTLOADER selected, click REVIEW & FLASH, then WRITE … SECTORS.
After an official M-VAVE update: M-VAVE's updater puts its own bootloader back. Install m-bootloader again afterwards.
Click FLASH BOOTLOADER, choose STOCK (FROM .FWSC), and pick an official M-VAVE firmware file for your model. Custom firmware files won't work for this.
Only what's different is written, and the unit comes back exactly as it was when you made the backup.
Restoring an old backup? Tick Keep this unit's bootloader so a newer m-bootloader stays on the unit.
Unplug the unit, then switch it off and on again. It starts with its firmware as usual.
sudo modprobe sg, do that in a terminal.Your Mac may remember the unit under an old name from an earlier firmware. Unplug the unit, open Audio MIDI Setup (in Applications → Utilities), choose Window → Show MIDI Studio, select the greyed-out entry for your unit (it may be called "USB Composite Device"), and press Delete. Then plug the unit in again.
That's a false alarm, which sometimes happens to a new release because it isn't signed yet. It's reported to Microsoft each time and usually clears within a few days. If you can't wait, and you downloaded it from the download page here (it comes from M-Flasher's releases on GitHub):
An older m-bootloader doesn't understand what a newer official FM-1 update left behind. Choose Boot app in its menu to start the firmware, then install the m-bootloader that comes with M-Flasher (see step 6).
That can happen on a unit with m-bootloader: M-VAVE's updater on an SMK-37 running a custom firmware, or Melodee's Return to official V15, for example. Nothing was changed. Use M-Flasher instead: restore a backup, or install the firmware and then put M-VAVE's bootloader back (see step 6).
Some USB ports are much slower with the unit. Try another one: a port at the back of a desktop computer, next to the video outputs, is often faster. M-Flasher suggests this too when it notices.
Ask in the issues on GitHub, and copy what M-Flasher's OPERATION LOG says. Your backups stay in Documents → M-Flasher → backups whatever happens.